| 浅析三边封制袋机的操作规程 |
| 添加时间：2017/8/31 16:45:56 浏览次数： |
| 1、开机前的准备工作 1, before the start of the preparation work 1）检查设备周围是否有灰尘、杂物，并将其清除。 1) check the equipment for dust, sundries, and remove it. 2）按生产通知单的要求上好塑料膜卷。 2) according to the requirements of the production notice, make a good plastic film roll. 3）按生产通知单和工艺文件调整好塑料袋的尺寸，安装好热封刀，并初步调好分切刀和热封刀的位置。 3) adjust the size of the plastic bag according to the production notice and the process document, install the heat sealing knife, and adjust the location of the cutter and the heat sealing cutter. 4）打开电源，按工艺文件要求设定热封刀温度。 4) turn on the power supply and set the temperature of the heat sealing cutter according to the requirement of the process file. 5）输入制袋的相关数据以及每扎的所需个数。 5) input the relevant data of bag making and the required number of each bundle. 6）选择色差较大的图案边沿左右调节光眼灵敏度，使其达到要求。 6) choose the edge of the larger color pattern, adjust the sensitivity of the eye light around, so as to meet the requirements. 2、开机 2, boot 1）启动主电机，低速运转，随即调整边位控制，将塑料膜对分在中间位置。 1) start the main motor, low speed operation, then adjust the edge control, the plastic film in the middle position. 2）调整左、右夹辊，使左右膜对齐，调整前后夹辊，使图案对正。 2) adjust the left and right pinch rolls, align the left and right membranes, adjust the front and rear clamping rollers to make the pattern correct. 3）调整热封刀，使其热封在塑料袋的要求范围。 3) adjust the heat seal knife so that it is sealed in the plastic bag. 4）调整分切刀片至所需位置，并把打孔位置调整到剪刀口。 4) adjust the slitting blade to the desired position and adjust the punch position to the scissors port. 5）初步调整好机速，取一次平出的样袋，进行初检，若未达到规定要求，再取一步平出的样袋进行热封值测试。 5) preliminary adjustment of machine speed, take a flat out bag, initial inspection, if not meet the requirements, and then take a step out of the flat heat sealed bag test. 6）将生产出来的塑料袋进行整理，并将存在质量缺陷的袋子选掉并按规定捆扎好。 6) will be produced plastic bags finishing, and the quality defects of the bag picked up, and tied as required. 7）由机台质检员进行检验，等检验合格后，贴上合格证，送入质检室抽检。 7) by the machine for the quality inspection, inspection qualified, post certificate, quality inspection and sampling into the room. 8）生产过程中，随时观察制袋情况发现异常，即时调整。 8) in the production process, observe bag making situation at any time, find abnormal, adjust immediately. 3、停机 3, stop 1）断开总电源开关，再断开各部位电源开关。 1) disconnect the main power switch, and then disconnect the power switch in each part. 2）清扫机器卫生及场地卫生，并将产品送到总检室。 2) clean the sanitation and sanitation of the machine, and send the product to the general inspection room. 3）作好当班记录，要求准确、整洁。 3) keep the records on duty and be exact and tidy. |
| 上一页 制袋机塑料的成分 |
| 下一页 制袋机工艺操作规程 |
Copyright © 技术支持：遨游网络